Product
Ingersoll Rand 54672530 Air Filter Element | N55/N75 Screw Compressor
Genuine Ingersoll Rand 54672530 air filter element for N55 and N75 screw compressors. 247 mm OD, 365 mm height, 5–10 μm filtration, fiberglass media with low pressure drop and high dust holding capacity. Cross-reference SA17281; matched by serial number.
- Export packaging & documentation support
- OEM / ODM customization available
- Sample and bulk order workflow
Product Overview
The 54672530 air filter element is a genuine Ingersoll Rand intake filter engineered for N55 and N75 series screw air compressors. Its high-efficiency synthetic fiberglass media captures airborne dust and particulate before it reaches the airend, protecting rotors, bearings, and shaft seals from abrasive wear and extending compressor service life.
This large cylindrical pleated element measures approximately 247 mm outside diameter and 365 mm overall height, with a red polyurethane (PU) end-cap seal. It cross-references HiFi Filter SA17281 and is compatible with several Atlas Copco part numbers.
Key Specifications
- Part number: 54672530
- Brand: Ingersoll Rand
- Component: Air filter element
- Machine compatibility: N55, N75 screw compressors
- Cross-reference: HiFi SA 17281
- Unit of measure: EA
- Availability: Normally stocked
Technical Data
Filtration Performance
- Filtration rating: 5–10 μm
- Filtration efficiency: approx. 99% @ 10 μm
- Filter class: F7–F8 (EN 779 / ISO 16890)
- Dust holding capacity: approx. 1.0–1.5 kg
- Beta ratio: β₁₀ ≥ 1000
Flow and Pressure Drop
- Rated air flow: approx. 10–13 Nm³/min (for 55–75 kW machines)
- Initial pressure drop: approx. 250–350 Pa at rated flow, clean
- Operating differential range: 350–600 Pa
- Alarm / final resistance: alarm at 700 Pa; replace at 900 Pa
- Energy impact: every 100 Pa increase in inlet pressure loss raises specific power by approx. 0.3%
Dimensions and Installation
- Outside diameter: 247 mm
- Inside diameter: 150 mm
- Overall height: 365 mm
- Weight: approx. 5 kg
- Effective filtration area: approx. 3.0–4.0 m² (pleated media)
- Mounting: center through-hole with end-cap seal
- Sealing: red polyurethane (PU) end-cap seal, double-sided
Construction Materials
- Media: synthetic fiberglass, yellow filter paper
- Media weight: approx. 120–150 g/m²
- Support: galvanized expanded metal mesh, inner and outer
- End caps: red polyurethane (PU)
- Seals: red nitrile rubber (NBR), top and bottom
- Bonding: polyurethane adhesive
Operating Conditions
- Operating temperature: -20 °C to 80 °C continuous; 100 °C short-term
- Relative humidity: ≤95% RH, no condensation
- Collapse pressure resistance: ≥4.0 kPa
- Features: low resistance, high dust holding capacity, suited to continuous industrial duty
Service Life and Storage
- Service life: approx. 4000 hours (8–12 months) under standard conditions; 2000–3000 hours in high-dust environments
- Shelf life: 36 months in original sealed packaging, dry at room temperature
Standards
- ISO 5011 — inlet air filter performance testing
- ISO 16890 / EN 779 — general ventilation air filter classification
- GB/T 14295 — air filters
- GB/T 6165 — air filter performance test methods
Maintenance and Installation
Replacement Interval
- Standard conditions: every 4000 hours or 8–12 months, whichever comes first
- High-dust conditions: every 2000–3000 hours
- Replace immediately if the media appears blackened or heavily loaded, or if differential pressure reaches 900 Pa
Installation Steps
- Shut down and isolate: switch off main power, apply lockout/tagout (LOTO), and confirm the machine has fully stopped.
- Open the filter housing: release the retaining bolts or clips and remove the cover.
- Remove the old element: pull out the old 54672530 element and check whether the seal remains in the housing groove.
- Clean the housing: wipe the inner walls and sealing surfaces with a clean cloth to remove dust and debris.
- Inspect the new element: verify part number 54672530; check media for damage, end caps for cracks, and red seals for ageing.
- Fit the new element: seat it vertically in the housing center so both seals contact correctly without misalignment.
- Refit the cover: reinstall the cover and tighten bolts or clips evenly.
- Start-up check: start the compressor and listen for any air leakage at the filter housing.
FAQ
Q: Is 54672530 a genuine Ingersoll Rand part?
A: Yes. 54672530 is a genuine Ingersoll Rand component with yellow high-efficiency media and a red polyurethane end-cap seal, designed for N55/N75 screw compressors.
Q: Which machines does 54672530 fit?
A: It fits Ingersoll Rand N55 and N75 series screw compressors. If you are unsure, provide the machine serial number and we will confirm.
Q: What is the cross-reference number?
A: HiFi Filter SA 17281. It is also compatible with Atlas Copco part numbers 1613950100, 1613951000, 1631043700, and 2255300129.
Q: What are the dimensions?
A: Outside diameter approx. 247 mm, inside diameter approx. 150 mm, overall height approx. 365 mm, weight approx. 5 kg.
Q: How do I know when to replace the air filter?
A: Replace when the media is visibly blackened or heavily loaded, when differential pressure reaches the 700 Pa alarm value, or at the 4000-hour / 8–12 month interval.
Compatible Machines
- N series: N55
- N series: N75
To confirm fitment for a specific unit, provide the compressor serial number for an exact match.
Related Parts
- SA 17281 — HiFi air filter element (cross-reference for 54672530)
- 1613950100 — Atlas Copco air filter element (compatible cross-reference)
- 1613951000 — Atlas Copco air filter element (compatible cross-reference)
- 1631043700 — Atlas Copco air filter element (compatible cross-reference)
- 2255300129 — Atlas Copco air filter element (compatible cross-reference)
- 88111901 — air filter element for SSR M37/M45
Note: For a 100% accurate match, provide the complete compressor serial number so we can check the original parts diagram and confirm current availability.